Exactly how to Replace a Bath Tub (Step By Step).
Exactly how to Replace a Bath Tub (Step By Step).
Blog Article
The article author is making several good points on Installing A Bathtub in general in the article down the page.
Setting up a bathtub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is likewise a moderately tough project. If the old bathtub is readily easily accessible, the task can move speedily; if you have to open up a wall to get rid of the old tub and also position the brand-new bathtub, the task is a lot harder. In either situation, the task is within a home handyman's abilities, although you will need an assistant to move out the old bathtub and also set in the brand-new one. Make sure you have actually certified on your own for the job as well as fit attempting it. Instead of working with a professional to take control of a halfway-completed project, it is much better to take into consideration employing one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This article will aid you install a new bath tub in your bathroom if you have already acquired a brand-new tub as well as don't require to transform the arrangement of your previous water system pipelines.
Your devices and material list need to comprise the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water. After doing so, activate the taps to drain any type of water staying in the system. The procedure of getting rid of the existing faucets can be fairly problematic due to the restricted access that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipes. When the supply pipelines have actually been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. Once the taps have been removed, the holes in the bath/basin will have to be cleaned of any old sealing substance.
Before proceeding to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end gives a link to the current supply pipelines.
If you need to fit a monobloc, then you will call for lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in location between the tap and also the sink. Safeguard the tap in place with the supplier given backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The previous kind ought to be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Making use of both wooden boards under its feet, position the tub in the required placement. The wooden boards are helpful in equally spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four small factors.
The next objective is to guarantee that the bathtub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the tub until the level reads degree.
To install faucets, fit the bottom of the outermost versatile faucet port to the ideal supply pipe by making a compression sign up with; then do the very same for the other faucet.
Turn on the water supply as well as check all joints as well as new pipework for leakages and tighten them if needed. Fill the tub as well as likewise examine the overflow outlet and also the normal electrical outlet for leaks.
Lastly, deal with the bath paneling as defined in the manufacturer's user's manual. Tiling and sealing around the bath tub should wait up until the bath tub has been made use of at least when as this will certainly settle it right into its last setting.
Planning for the Setup
To start with, the supporting structure supplied with the bathroom should be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the taps unit to avoid pressure on the bath tub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final setting.
Tiling Around the Tub
In the location where the bath satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to crack a rigid seal, causing the water to permeate the wall between the bathroom as well as the tiling, causing difficulties with wetness and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components as well as fittings. They are sold in tubes and cartridges, and can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of soaked newspaper or soft rope. Remember to constantly load the tub with water before sealing, to permit the activity experienced when the bathtub is in use. The sealer can fracture relatively early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily readily available on the marketplace. It is recommended to fit the tiles utilizing water-resistant or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate more info about Installing A Bathtub? Try to leave a remark down the page. We will be delighted to see your views about this blog entry. Hoping to see you back again later on. In case you enjoyed our blog post plz make sure you remember to share it. Thank you so much for going through it.
Book Now! Report this page